China Good quality High-Intensity and High Precision and Wear Resistance Stainless Steel Sprocket with Free Design Custom

Solution Description

Basic Details.


Simplex, Duplex, Triplex

Sprocket Model:

three/8″,1/2″,5/8″,3/4″,1″,1.twenty five”,1.fifty”,1.seventy five”,2.00″,2.twenty five”,2.00″,2.twenty five”,2.fifty”, 3″

Teeth Number:

9-a hundred




1571, 1045, SS304 , SS316  As Per Consumer Ask for.

Functionality Remedy:

Carburizing, High Frequency Remedy, Hardening and Tempering, Nitriding

Surface Remedy:

Black of Oxidation, Zincing, Nickelage.

Attribute Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc
Layout criterion ISO DIN ANSI & Customer Drawings
Application Industrial transmission tools
Package Picket Circumstance / Container and pallet, or made-to-purchase



Quality Inspection:

Self-check and Final-check out


ODM&OEM, Trial Order Available and Welcome

Benefit Top quality initial, Service very first, Aggressive cost, Quickly delivery
Shipping Time 10 times for samples. 15 days for official order.


Set up AND Using

The chain spocket, as a travel or deflection for chains, has pockets to hold the chain hyperlinks with a D-profile CZPT segment with flat aspect surfaces  parallel to the centre plane of the chain hyperlinks, and outer surfaces at right angles to the chain link centre airplane. The chain backlinks are pressed firmly in opposition to the outer surfaces and every of the side surfaces by the angled laying surfaces at the foundation of the pockets, and also the assist surfaces of the wheel body jointly with the conclude sides of the webs formed by the major and trailing partitions of the pocket.


When CZPT new chain spoket it is quite critical that a new chain is equipped at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with aged sprockets will trigger speedy put on.

It is critical if you are setting up the chainwheels oneself to have the factory provider manual particular to your model. Our chainwheels are produced to be a direct CZPT for your OEM chainwheels and as this kind of, the installation need to be performed in accordance to your designs support guide.

In the course of use a chain will stretch (i.e. the pins will dress in creating extension of the chain). Making use of a chain which has been stretched much more than the over optimum allowance brings about the chain to journey up the teeth of the sprocket. This brings about harm to the ideas of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely via the top of the tooth, fairly than the whole tooth. This benefits in severe wearing of the chainwheel.


Requirements businesses (this sort of as ANSI and ISO) keep specifications for style, dimensions, and interchangeability of transmission chains. For illustration, the pursuing Table displays info from ANSI regular B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) produced by the American Modern society of Mechanical Engineers (ASME). See the references[8][9][ten] for extra details.

ASME/ANSI B29.1-2011 Roller Chain Common SizesSizePitchMaximum Roller DiameterMinimum Final Tensile StrengthMeasuring Load25

ASME/ANSI B29.1-2011 Roller Chain Normal Dimensions
Size Pitch Highest Roller Diameter Bare minimum Final Tensile Power Measuring Load
25 .250 in (6.35 mm) .130 in (3.thirty mm) 780 lb (350 kg) eighteen lb (8.2 kg)
35 .375 in (9.fifty three mm) .two hundred in (5.08 mm) 1,760 lb (800 kg) 18 lb (8.2 kg)
41 .500 in (twelve.70 mm) .306 in (7.seventy seven mm) one,500 lb (680 kg) 18 lb (8.2 kg)
forty .500 in (twelve.70 mm) .312 in (7.ninety two mm) 3,125 lb (1,417 kg) 31 lb (14 kg)
50 .625 in (fifteen.88 mm) .400 in (ten.sixteen mm) four,880 lb (2,210 kg) 49 lb (22 kg)
60 .750 in (19.05 mm) .469 in (11.91 mm) seven,030 lb (3,one hundred ninety kg) 70 lb (32 kg)
80 one.000 in (twenty five.40 mm) .625 in (15.88 mm) 12,five hundred lb (5,seven-hundred kg) one hundred twenty five lb (fifty seven kg)
one hundred 1.250 in (31.seventy five mm) .750 in (19.05 mm) 19,531 lb (8,859 kg) 195 lb (88 kg)
one hundred twenty one.500 in (38.ten mm) .875 in (22.23 mm) 28,one hundred twenty five lb (12,757 kg) 281 lb (127 kg)
a hundred and forty one.750 in (44.forty five mm) one.000 in (twenty five.forty mm) 38,280 lb (17,360 kg) 383 lb (174 kg)
160 two.000 in (50.eighty mm) one.125 in (28.fifty eight mm) fifty,000 lb (23,000 kg) 500 lb (230 kg)
one hundred eighty 2.250 in (fifty seven.15 mm) 1.460 in (37.08 mm) 63,280 lb (28,seven-hundred kg) 633 lb (287 kg)
200 2.500 in (sixty three.50 mm) one.562 in (39.67 mm) seventy eight,one hundred seventy five lb (35,460 kg) 781 lb (354 kg)
240 3.000 in (76.20 mm) one.875 in (forty seven.63 mm) 112,500 lb (fifty one,000 kg) one,000 lb (450 kg

For mnemonic functions, underneath is an additional presentation of key dimensions from the exact same standard, expressed in fractions of an inch (which was component of the pondering driving the selection of favored quantities in the ANSI standard):

Pitch (inches) Pitch expressed
in eighths
ANSI normal
chain quantity
Width (inches)
1four two8 2five one8
38 threeeight three5 316
1two foureight fourone 14
one2 48 4 516
58 five8 5 3eight
threefour sixeight six one2
one 8eight eight fiveeight

1. The pitch is the length between roller facilities. The width is the length in between the link plates (i.e. a bit far more than the roller width to allow for clearance).
2. The proper-hand digit of the standard denotes 0 = typical chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the quantity of eighths of an inch that make up the pitch.
four. An “H” adhering to the common variety denotes heavyweight chain. A hyphenated quantity subsequent the normal number denotes double-strand (2), triple-strand (3), and so on. Therefore 60H-3 denotes variety sixty heavyweight triple-strand chain.
 A common bicycle chain (for derailleur gears) makes use of slim 1⁄2-inch-pitch chain. The width of the chain is variable, and does not have an effect on the load capability. The a lot more sprockets at the rear wheel (traditionally 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are bought according to the quantity of speeds they are developed to operate with, for instance, “ten speed chain”. Hub equipment or one velocity bicycles use 1/2″ x 1/8″ chains, exactly where 1/8″ refers to the optimum thickness of a sprocket that can be employed with the chain.

Generally chains with parallel shaped links have an even quantity of backlinks, with every slim hyperlink adopted by a broad 1.Chains developed up with a uniform kind of link, narrow at 1 and wide at the other stop, can be produced with an odd quantity of hyperlinks, which can be an advantage to adapt to a special chainwheel-length on the other side such a chain tends to be not so sturdy.

Roller chains produced utilizing ISO common are sometimes known as as isochains.


WHY Select US 

one. Reliable High quality Assurance Technique
2. Slicing-Edge Personal computer-Controlled CNC Equipment
three. Bespoke Solutions from Extremely Knowledgeable Experts
four. Customization and OEM Available for Particular Software
5. Substantial Inventory of Spare Parts and Equipment
6. Properly-Created Around the world Advertising and marketing Community
seven. Productive Following-Sale Service Method


The 219 sets of superior computerized generation tools provide ensures for high item top quality. The 167 engineers and experts with senior specialist titles can style and develop products to satisfy the specific requires of customers, and OEM customizations are also offered with us. Our sound international service community can supply customers with timely following-product sales technical providers.

We are not just a maker and provider, but also an sector advisor. We function pro-actively with you to provide skilled advice and product suggestions in get to conclude up with a most value effective product available for your specific application. The customers we serve globally assortment from conclude consumers to distributors and OEMs. Our OEM replacements can be substituted wherever essential and suitable for the two restore and new assemblies.


Ep prefabricated metal sprockets are made of C1045 steel, induction hardened or warmth-handled steel, four hundred – 500 BHN hardness. You should specify the supplies you require. Unless normally asked for, the outside diameter of the hub must be adequate to accommodate the essential holes and keyways. Keys to these items are not supplied unless requested or installed on the shaft. Split sprockets for welding or split sprockets for bolts offer an cost-effective way to install sprockets on shafts where removing of the shaft assembly is prohibited. A lot of measurements of sprockets are outfitted with holes, keyways, and established screws. Discs or partly concluded sprockets are also stocked. For lengthy sprockets and idlers, specify the chain size employed.
Drum sprockets: These sprockets are usually broader to enhance the all round surface area contact among the sprocket and chain. This decreases stress on both sections, generating a more sturdy method for weighty haul conveyors.

China Good quality High-Intensity and High Precision and Wear Resistance Stainless Steel Sprocket     with Free Design Custom

Chain And Sprocket

As one of the chain and sprocket manufacturers, suppliers, and exporters of mechanical products, We offer chain and sprocket and many other products.

Please get in touch with us for details.

Manufacturer supplier exporter of chain and sprocket.

Recent Posts